Fender Guitar Parts Usa For Sale (2024 Update)

Better than any locking tuner, you just have to measure the string to the second peg above the one you're using, cut it and put it in. When you get to the unwound ones, clip a little shorter (can't tell you how to measure, I figured it out by trial and error. I would estimate 3 wraps by sort of wrapping it loosely, then cut). Perfect match to the vintage F tuners made on the great strats of yore, you can age them to match by fuming the finish with muriatic acid. Place the tuners on an upside down bowl in a piece of tuperware with an inch or so of acid. Seal the lid. Place in a bath of hot water, and the acid will heat and evaporate. After 10 – 15 minutes check the level of chrome removal. You can always do more, but you can't easy put chrome back on. Rinse with cold water when you're done. RAWK ON!!!!ki_jaybones

I build custom Strat/Tele's so this may not apply to all but…. Like others said this peg uses press-fit front bushing style similar to low cost Squire Strat. For standard diecast pegs I drill 10 mm diameter holes on peg head. I use aftermarket necks with 8 mm diameter hole (I remember it is same as low cost Squire). What I do on 8 mm holes for this peg is I drill 4 mm deep 23/64 (9.1 mm??) diameter counterbore holes to accommodate the bushings. I strongly recommend using drill press not hand drill for this. Also for a better support of peg shaft, I made Teflon sleeves to fill the peghead holes of 8 – 10 mm with silicone grease. One minor issue I have is peghead of some aftermarket Tele neck is a little undersized so I need to file the end peg (High E) a bit to fit.Basement Blues

I got these to replace the stock tuners on my Fender Modern Player Thinline Tele. The stock tuner's ratio was something like 7:1 and made the guitar difficult to tune (why do they even make these?) These replacement tuners are much easier to tune precisely because of the 14:1 ratio and they were a simple, no mod, replacement.MoFoYa

Look great, cheap materials. 1 tuner stripped right out of the box, won't turn the spindle to tighten the string, a second tuner is binding, probably going to strip also. These are Fender branded, very disappointed. Gotoh or Wilkinson for replacementsrainman628

I bought this for a partscaster project I was working on since I had read that it will bolt directly to a Squier SE Special body. I am here to verify that it bolts onto the Squier SE body without issue but cannot say whether it fits other Squier models (although I did read that it is too deep to work on the thinner Squier "Affinity" model bodies). I like the stamped saddles and the high mass block compared to the Squier unit. Side Notes: The string and mounting bolt spacing is not the same as the "vintage" Fender models (i.e.: it would not work on my MIM Fender Road Worn 50's Strat for instance). You will also need a Standard Mexican Fender tremolo bar (PN 099-2310-100), since the import one has different threads. Also, the Fender Mexican spring claw is wider than the one mounted to the Squier SE, so I just kept the original SE one in place, which works fine. Anyway, if you want an inexpensive upgrade for your lower end import Strat, I can attest to the quality of the Fender Mexican Tremolo bridge assembly… Good Luck!danzprod

I purchased this to better my sustain and after installation. The sustain was lasting to long almost five seconds, very hard to intonate. I new something was wrong. I checked the cavity and found one corner touching and after removal l was able to clear that up. Now it's as it was meant to be. Great tone increase and actually added to my playing comfort. I have the claw spring adjusted one half inch out and even making my trem exactly at 1/8 above the guitar surface. It's how l have always setup my strats and all my bends are more comfortable than with the old block. My sustain is around three seconds now and allows my compressor sustainer pedal to work properly. It's a vast improvement to tone. I can actually use 1 through 5 and all sound great no more over the edge quack and the other end not as dark. Definitely recommend, just check before you button it up that the block isn't touching the body or your notes will wring out on top of one another and most compressor s can't keep up to fix it. Custom shop neck American vintage Clapton fender noisless and believe it or not l replaced my worn out body with a new squire standard same neck pocket size just basswood it's awesome body $60 and of course the block had to go. If you upgrade your body measure the back of the neck pocket thickness and make sure it matches and dump the block and go fender big. Thanksatexx

I love the aged look of the pickup covers and knobs. I have ordered many over the years. The tremolo cover does not match at all and usually has a mint green color. That part of the kit is a waste. I have piles of them which I cannot use. The best look for your Strat is a W/B/W pickguard with matching tremolo cover and these pickup covers and knobs. I will continue to buy the kit. I have tried several others and they are always lacking.lawellness

Everything was fine except for the tremolo cover that fits on the back of the guitar. It was too small and the screw holes would not align with the factory drilled holes. My Stratocaster was a standard design made in Mexico. So it should have fitted.graleat-72

These pickups have the sound I was looking for. Clear and articulate while sounding great with overdrive and distortion on. Better sounding than some more expensive pickupsromanoid3fmm

Very good part and good fitment to Fender Stratocaster. It's a genuine Fender part so the quality is good. I used to retrofit this to a 1981 Strat and it did the job just fine. I would recommend this bridge assembly.darrellgw

The bridge has a solid feeling heavy block and nice looking bent steel traditional saddles. Be aware that bent steel saddles do have the potential to develop a buzz from time to time, particularly on the high string. Smoothing the top of the saddle with some very fine wet and dry will usually fix this. You might also like to source shorter grub screws or shorten them yourself by grinding down the bottom of the screws, as they poke up into your hand when palm muting.mattguitarroberts

As a hobby, design and assemble the guitar. Needed genuine Tremolo Kit. Keeps system. High quality materials and workmanship. I'm happy! Found what I was looking for.mishmikha

#1 is the positive fitting bar instead of the screw in arm that's never where you need it. For a non locking system it's hard to beat.llar-c-l3nr6bmlk8

I've played a lot of different Strats over the years and while they all had "that Strat sound" to varying degrees, the Fat '50s achieve seem to be the most authentic. By adding a treble bleed and turning down the volume a bit, I can get those classic chimey tones from the 50s and with the volume all the way up, I can get the bigger sounds from the 60s. The cleans are sparkling, but they sound great running through higher gain amps as well. Compared to pickups like the Texas Specials, these are not harsh to my ears, even in the bridge position. If you're looking for the solid Start sound, you can't go wrong with these,BOCTOK

The Fender Mexican made 2017 Stratocaster is a nice guitar and as a standard out of the box guitar is good. One easy way to upgrade the sound is by installing the Fender Custom Shop Fat 50's pickup set. I measured the ones on a custom shop 59 before purchase to be sure of string alignment. I purchased a set and fitted them in about half an hour, fortunately my Mex ST had an Oak type 5 way and full size pots so no more upgrade work needed there. I did change the pot knobs and switch knob to white to match the new pickup covers. I installed a new set of strings, the pickups were test adjusted and sound great, a nice full sound, the front one is very rounded and clear, the middle is a classic sound and the back nice and strong. I was after a Shadows style of sound and these pickups did not disappoint. They give a clear sound and the right sound if you are looking for pure vintage tone.matt66red

I waited 5 months to write this review, I'll try to be unbiased. I replaced the stock ceramic pickups from a Fender Standard MIM. It's my first change of pickups ever, and the first time I play a guitar that sounds so classic, so I can not tell about the difference with a higher end model of Strat or a vintage one, but here goes my opinion: This pickups totally rock, well they don't only do rock, they play everything you want to hear from a instrument called "guitar", that means, 6 strings thru a wood body, they deliver the classic and just necessary electric guitar experience. No gimmicks, just the real thing, classic clean sound, lots of harmonics, dynamic sound, and driven sound wonderful, because they can be strong too, classic surf rock sound here. Took me a couple of days to adjust the proper height, the Alnico V magnets are strong so you have to be delicate to find the right spot for the three PUs, but once you are there, they are marvellous. The three pickups are pretty much the same, states the box, but the three positions are there, and the case with the medium pickup is a great surprise, it sounds very nice, very "middy" usable position, sounds as a custom medium pickup. By all means, you don't need no more that a old school Stratocaster guitar, as Leo designed, to be happy. Cheers. Rock on, blues on, jazz on, jangly on, surf''s up!Oscar the mendigo.

This is a really nice pick guard. Fit is perfect. Protective film so no scratches. Package well. Everything as described. Very pleased. All holes do not line up with Korean Squire but it fits perfectly. This is for an original Stratocaster or un-drilled blank body.brazosducati

I came into possession of a Fender Partscaster for which I paid $200. I didnt know what parts were OEM or from what models they came. I just knew the sky blue burst was gorgeous and I had to have it. As it turned out, the body was from Fenders American Elite line making the price an absolute steal. Long story short all of the other parts needed to be swapped out. Once the neck was swapped the truss rod adjuster on the heel wouldnt fit with the non-Elite pickguard. The pickguard was a proper mint green but wrong model. I dremeled the notch out so I could temporarily use it. I finally invested in the proper pickguard a couple of years later and I cant be happier with the quality. Quite glad I didnt buy a cheap Chinese knockoff like I had thought of doing. All thats left is to swap out the Fender vintage bridge with the Elite/Deluxe model. And lastly swap out the cheap Tex-Mex pickups for some 60s era handwound models. Theyll be the only non-Elite part since I wont be getting the appropriate Noiseless Gen 4 type.rangerjack

I bought this for a partscaster project I was working on since I had read that it will bolt directly to a Squier SE Special body. I am here to verify that it bolts onto the Squier SE body without issue but cannot say whether it fits other Squier models (although I did read that it is too deep to work on the thinner Squier "Affinity" model bodies). I like the stamped saddles and the high mass block compared to the Squier unit. Side Notes: The string and mounting bolt spacing is not the same as the "vintage" Fender models (i.e.: it would not work on my MIM Fender Road Worn 50's Strat for instance). You will also need a Standard Mexican Fender tremolo bar (PN 099-2310-100), since the import one has different threads. Also, the Fender Mexican spring claw is wider than the one mounted to the Squier SE, so I just kept the original SE one in place, which works fine. Anyway, if you want an inexpensive upgrade for your lower end import Strat, I can attest to the quality of the Fender Mexican Tremolo bridge assembly… Good Luck!danzprod

I purchased this to better my sustain and after installation. The sustain was lasting to long almost five seconds, very hard to intonate. I new something was wrong. I checked the cavity and found one corner touching and after removal l was able to clear that up. Now it's as it was meant to be. Great tone increase and actually added to my playing comfort. I have the claw spring adjusted one half inch out and even making my trem exactly at 1/8 above the guitar surface. It's how l have always setup my strats and all my bends are more comfortable than with the old block. My sustain is around three seconds now and allows my compressor sustainer pedal to work properly. It's a vast improvement to tone. I can actually use 1 through 5 and all sound great no more over the edge quack and the other end not as dark. Definitely recommend, just check before you button it up that the block isn't touching the body or your notes will wring out on top of one another and most compressor s can't keep up to fix it. Custom shop neck American vintage Clapton fender noisless and believe it or not l replaced my worn out body with a new squire standard same neck pocket size just basswood it's awesome body $60 and of course the block had to go. If you upgrade your body measure the back of the neck pocket thickness and make sure it matches and dump the block and go fender big. Thanksatexx

I put together my own Stratocaster, the build took about a year and a half as genuine fender quality parts can get pricey. The neck plate made my strat look legit and high quality. As a professional musician I'm a stickler on quality parts for my instruments and I can tell tell you with 100% confidence that buying genuine fender parts for your build is worth every penny they just look, feel and sound good.Pablo

Be aware these are about 19 grams in weight and are made of some kind of aluminium alloy. The old strat plates were made of some other heavier non magnetic metal. My strats old plate weighed in at 59 grams; both are roughly about 2.2 mm thickness. The fender f plate and vintage plate are both chrome plated steel, (well magnetic material anyway). The vintage plate is about 32 grams and very thin at about 1.2 mm. The f plate is about 1.5 mm, and a little heavier the vintage, (on guitar so could not weigh). The corona plate seems strong and it has a good chrome finish. I marked it down one star due to the radical weight difference over previous plates, but I'm sure it is strong enough to last. Fender also confirmed that these plates are correct and used on newer strats.goldfinger1976

Nice neck plate. Heavy steel, and deep stamping on the logo. The screws could be better suited but all-in-all, a good price and an above average quality product.lawrsow0

I first discovered these when purchasing a Fender American Deluxe Strat. Fender only puts them on the American Deluxe Strats and Teles, so far as I know. Since then, I have purchased these and put them on three other of My Fender Teles and Strats. These are a perfect way to upgrade, if your Fender neck has the two-pin guide holes, like most of their modern necks (vintage style excluded). These really are the smoothest Fender machine heads/tuners I've ever found. The lower priced two pin tuners as used on the Player series just aren't as smooth and it seems like the gear ratio is different, too. maybe lower than the Player machine heads, like 18:1. Yes..more expensive, but even without the locking device, well worth it, IMO. The pic is a Tele I recently built with V-Mod pups and 12' radius fret board. I just installed the tuners the other day. The guitar deserved these and I love 'em!songs60s

Have had these new Fender locking tuners on my Stratocaster for a few weeks now, and I must say that I really like them! I think one of the big benefits of locking tuners on a Fender with a whammy bar is that there are no wraps of the string on the tuning pegs, the wraps dont always go back the same way after returning from a dive. Also the new tuners seem to have a little more weight to them than the original tuners. The added weight and mass seem to make the tone of the guitar a little more solid with possibly a bit more sustain. I definitely noticed a big improvement with tuning stability after the first time of doing some dives on the guitar. The feel of the tuners while actually tuning the guitar is very nice too, very smooth and precise. I would not hesitate to buy these tuners again to put on my other Fenders.stratm_88

I bought these for my American Performer Strat. I had no issues with tuning. The vintage tuners that came with it stayed in tune just fine. Had problems with strings slipping while changing them and it was very frustrating. At first I was concerned because they came with no installation instructions and I am not good mechanically at all. Found instructions on how to install them onto the guitar and how to install strings by looking on the internet. So,so easy! All you need is a pair of pliers. Loosen the nut, remove the old tuner and put the new one on. If you are installing on a Fender Strat the holes line up with the two pegs on the locking tuner and they pop right in and you tighten the nut. That simple. To install the string you just pull the string through the peg as tight as you can by hand, tighten the bottom knob which locks the string and cut the string and tune. So, so simple and efficient. I have no problem installing new strings any more! Quick and easy. Everyone should have these. Well worth the money by far!Morningdew

This should have been the standard bridge on the Thinline Cabronita Telecaster, since it matches up with the pickup pole spacings much better than what comes on the guitar. The three mounting holes aren't an exact match, but install the middle screw first and then go into the outside two holes at a slight angle and it will work fine. Also keeps the two E strings farther in from the edges of the fretboard.duhvoodooman

Solid, well built. Just make sure you know this does not fit a vintage style 2 3/16 hardtail guitar. The string hole spacing on both the mounting screws and string holes are not the same. It can be made to work if you are ok with it not being perfect. Otherwise it is a great bridge. I prefer the vintage style stamped saddle hardtail bridges because they are 1/3 the cost.mathewsguitarworks

Tuners are solid and work — not locking type, but stays in tune. Installation takes either a neck with the two little guide-holes all ready to go, or else some skill with a small drill bit. Put it into place and tighten down enough to leave two faint dents on the headstock, then remove and drill. Tape a stop guide so you don't drill too far through the neck, just deep enough for the wee pegs.zippinski

The only downside to these tuners is that they require two holes to be drilled in the back of the headstock alongside the 10mm hole to locate two pins extending from each tuner that prevent it twisting around under string tension. If your headstock is pre-drilled, no problem, but if it isn't you will have to do this yourself. I used a Dremel with a dentists' drill and a steady hand. Other than this they look great, very tidy and most importantly work well. They hold tune perfectly. Recommended.johthoma270

These are the tuners that came stock on my E4 Fender American Standard. They have a smooth feel, and stay in tune well. The tuners have worked reliably since I bought the guitar in 1985. I also have several other guitars with these tuners, and they all function perfectly. I think that the tuners improve the sound by making sure that the strings stay in tune. Also, these tuners make good contact with the neck, and don't vibrate like some marginally acceptable Chinese tuners, found on some Squiers (and other budget guitars), thereby better transferring vibration to and from the neck and strings. Just my two cents.Bill

Sembra che tenga meglio l'accordatura, ma la vite è più sottile del foro sulla paletta, ho provato a sostituirla ma al momento non l'ho trovata cromata. Spero che il serraggio con la nuova vite sia solido altrimenti proverò ad occludere il foro con colla e stecchino e poi rifare il foro per la vite più piccola originale del kit abbassacorde acquistatoBartolomeo Di Pierro

This should have been the standard bridge on the Thinline Cabronita Telecaster, since it matches up with the pickup pole spacings much better than what comes on the guitar. The three mounting holes aren't an exact match, but install the middle screw first and then go into the outside two holes at a slight angle and it will work fine. Also keeps the two E strings farther in from the edges of the fretboard.duhvoodooman

Solid, well built. Just make sure you know this does not fit a vintage style 2 3/16 hardtail guitar. The string hole spacing on both the mounting screws and string holes are not the same. It can be made to work if you are ok with it not being perfect. Otherwise it is a great bridge. I prefer the vintage style stamped saddle hardtail bridges because they are 1/3 the cost.mathewsguitarworks

I got this neck to replace the one I had on my Squier FSR Bullet Telecaster (in Metallic Purple with Maple Fretboard). This telecaster has a Maple neck with a normal C shape and felt really unrefined for a "Fender" neck. I decided to get this Fender Telecaster Standard Replacement Neck with a Modern C shape neck. This new actual Fender neck was a drastic change in quality and performance. Here's just a quick Pros and Con of this product. PROS: Real Fender Product – Because this is an official Fender product, the neck replacement on my Squier was seamless and very simple. Modern C – Makes a better feeling guitar when playing compared to the normal C shape neck. Satin Neck Finish on back – The neck is very smooth feeling when playing. The finish on the back of the neck doesn't get in the way of you playing fast. This helps if you have sweaty hands when playing. Gloss fretboard – This makes a difference because if doesn't feel like your fingers are sticking to the fretboard. Medium Jumbo Frets – Just feels nice when moving around the fretboard. Bending strings feel nicer than my old Squier frets. Pre Drilled Holes for Tuners – I already had Fender locking tuners. So it was a simple swap with no mods needed. CONS: Nut not slotted – I don't understand why the NUT isn't slotted at least for common string size. It is very slightly to get you started but you would need a file. I just used the low E strong and used it like a file but it didn't come out too well and I've had to buy a new nut that comes preslotted. No predrilled String tree hold – This really wasn't too much of a problem but it's scary if you get it wrong. Overall, I'm very happy with my purchase after two weeks of everyday playing with it. This was a much needed upgrade from my Squier telecaster neck I had.C. Barona

this is my 4th roasted neck and I can't recommend them enough. especially if you live on or near the water. I can pull out my strat or tele after not playing them for a few days and they are right in tune look at the quality that is put into them and you'd agree. when screwed to a sunburst or pastel colored body they just really enhance the look of your instrument. the cost of the roasted neck is something you gotta think about like do you really want to spend that kinda Ching on a neck? hell you can buy a standard neck for less or even buy an after market neck and play the same its all about the stability of the wood that closed the deal for me. dig down deep in yer pocket and pony up the Ching for one of these I'm pretty sure you be pleased you did. I have them mounted to Mexican fenders and American fenders all have mated up perfect and very little fret work was needed this is my experience with these necks and you will find the same. in short I dig mine and will in the future will only use these beautiesho-joe56

perfect fitment into a MIM fender body. finish was flawless and the dark maple is beautiful. mistake made on my part, not fender….. the roasted maple has so much less give than standard maple. I should have thought about that with all of the moisture being removed from the wood. I used fender press fit tuner bushings and installed them with a C-clamp as I always have. I heard the headstock crack as I was installing the D string bushing and my heart sank. Luckily, I was able to inject some wood glue and clamp it overnight to close it up, but I reamed out the G tuner bushing and learned my lesson. use care when installing the tuner bushings on anything roasted as the fibers in the wood simply will not compress the same way another neck would.Grey

These Genuine Fender Dome Knobs have a great solid feel, and look great too. They're a nice weight also. I actually bought them as replacement knobs for a newer G&L LB100 "P" bass. The knobs on there didn't feel as solid, weren't domed and the diamond cut pattern didn't have as smooth a finish. These are a real improvement.jag67jaguar

I have to say, I don't normally write reviews for product – but this little item changed my mind. I bought one to finish up a parts-o-caster home build, where it was matched with a different knob type. After mounting this one on the guitar, I immediately pulled off the other type and ordered another one of these domed nickel knobs. They are, simply put, the best Tele style knob I have ever used!jagoldtop

ORIGINAL fender parts are always the best way to go whether your replacing old ones or building your own new monster. You can feel it in your hands when you hold them. I buy all my parts from Guitar Audio. They are a fantastic company. Well priced and quick to deliver. Real happy with the knobs. My second build with genuine Fender parts from Guitar Audio and I'll use them on all to come.candelljr123

I got this neck to replace the one I had on my Squier FSR Bullet Telecaster (in Metallic Purple with Maple Fretboard). This telecaster has a Maple neck with a normal C shape and felt really unrefined for a "Fender" neck. I decided to get this Fender Telecaster Standard Replacement Neck with a Modern C shape neck. This new actual Fender neck was a drastic change in quality and performance. Here's just a quick Pros and Con of this product. PROS: Real Fender Product – Because this is an official Fender product, the neck replacement on my Squier was seamless and very simple. Modern C – Makes a better feeling guitar when playing compared to the normal C shape neck. Satin Neck Finish on back – The neck is very smooth feeling when playing. The finish on the back of the neck doesn't get in the way of you playing fast. This helps if you have sweaty hands when playing. Gloss fretboard – This makes a difference because if doesn't feel like your fingers are sticking to the fretboard. Medium Jumbo Frets – Just feels nice when moving around the fretboard. Bending strings feel nicer than my old Squier frets. Pre Drilled Holes for Tuners – I already had Fender locking tuners. So it was a simple swap with no mods needed. CONS: Nut not slotted – I don't understand why the NUT isn't slotted at least for common string size. It is very slightly to get you started but you would need a file. I just used the low E strong and used it like a file but it didn't come out too well and I've had to buy a new nut that comes preslotted. No predrilled String tree hold – This really wasn't too much of a problem but it's scary if you get it wrong. Overall, I'm very happy with my purchase after two weeks of everyday playing with it. This was a much needed upgrade from my Squier telecaster neck I had.C. Barona

this is my 4th roasted neck and I can't recommend them enough. especially if you live on or near the water. I can pull out my strat or tele after not playing them for a few days and they are right in tune look at the quality that is put into them and you'd agree. when screwed to a sunburst or pastel colored body they just really enhance the look of your instrument. the cost of the roasted neck is something you gotta think about like do you really want to spend that kinda Ching on a neck? hell you can buy a standard neck for less or even buy an after market neck and play the same its all about the stability of the wood that closed the deal for me. dig down deep in yer pocket and pony up the Ching for one of these I'm pretty sure you be pleased you did. I have them mounted to Mexican fenders and American fenders all have mated up perfect and very little fret work was needed this is my experience with these necks and you will find the same. in short I dig mine and will in the future will only use these beautiesho-joe56

perfect fitment into a MIM fender body. finish was flawless and the dark maple is beautiful. mistake made on my part, not fender….. the roasted maple has so much less give than standard maple. I should have thought about that with all of the moisture being removed from the wood. I used fender press fit tuner bushings and installed them with a C-clamp as I always have. I heard the headstock crack as I was installing the D string bushing and my heart sank. Luckily, I was able to inject some wood glue and clamp it overnight to close it up, but I reamed out the G tuner bushing and learned my lesson. use care when installing the tuner bushings on anything roasted as the fibers in the wood simply will not compress the same way another neck would.Grey

The parts worked just fine. I had gotten this one partscaster stratocaster JMP made in america bdy. didn't realize the claw & springs weren't fender till I went to adjust the claw to set up tremolo the 2 screws were real skinny and way too short. So I replaced them with the real deal original vintage Fender parts the only way to go. I had to drill the 2 holes bigger and deeper to allow for the correct screws but the the tremolo works real good now and is actually staying in tune better than my of my other strats that are all real strats pretty interesting. it is working great.. real good price and quick delivery as well..Mike

Switching from the 3 stiffer springs which came stock with my guitar, to 5 springs of the vintage type has added a little more of that "stratness" to the tone of this guitar as well as enhancing the sustain just a little bit. A very easy and inexpensive upgrade which is well worth it to me. Try it; you'll probably like it. Some people may not like to "hear the springs" on their instrument, but in my opinion, that sound is a part of what defines the strat character.benjaminrait

These springs work great as they are a genuine Fender product. My only objection was that the bridge end of the spring fit very tightly into my Fender Squire Standard two point tremolo bridge. I had to use a tool to get the end far enough into the bridge. Other than that (no point takin away) the springs did the job that they were designed to do.drums1961