Fender Bass Guitar Accessories For Sale (2024 Update)

Functional tuners although on the heavy side which tends to cause a bit of neck dive. The American Special and others may require the larger tuner bushings which are not included. Don't know why there is not one size. The larger Mexican tuner bushings 005-1532-049 which are 18mm as opposed to the smaller ones which are included. Best to check the size of the peg holes first.mikecd1

Good drop-in replacement for MIM Standard basses. I have a MIM Precision bass I bought from someone who had upgraded all the parts, and then pulled them off before selling, so I needed new hardware. After trying a cheaper import set of tuners and finding they didn't quite fit without needing new holes, I decided to spend twice as much for these. They're much better quality, and they're the original equipment that it came with from the factory. Smooth turning, sturdy feel, holds tune, looks nice and shiny. All around great gear at a decent price.musicmakerdeals

Pre-bent to a slightly tighter radius. This eased installation a great deal. Not cut to uniform lengths, but they were all long enough to get the job done. The cuts were a little sloppy, but they must be filed and finished at the ends either way. Needed very little levelling and dressing. Overall great quality fretwire with uniform radius bends.20 Fingers McGee

The fret wires come in over sized lengths with plenty to work with. I was concerned that the grooves from the removed large jumbo frets would be too loose but they have more than enough tangs that fill and grips the rosewood which can be a bit 'chippy'. I had to adjust the radius of each one which was a bit of a pain that would have been much easier if they left them straight. They filed, leveled and crowned well and are just a bit taller than expected it good quality.001Berek

They are a high quality precision fret wire! After 3 of the Fender frets were installed, I contnually checked fret rocking and was suprised at the results, only 3 frets needed minor leveling after installation was completed. Now my import guitar plays like a High End instrument.timmci85

I bought these when I upgraded the pots in my MIM jazz bass to obsidianwire pots (the stock knobs dont work). The knobs went on and tightened just fine, quality is what youd expect from Fender – awesome!Im not sure why other reviewers had difficulty tightening the set screws – theyre a 5/32 if I remember right which is a pretty standard sized hex wrench.rapistan

I had bought a used squire jazz bass. The person who owned the jazz bass had put strat knobs on it. I really wanted these knobs for there appearance and practicality. When I first got them, I thought that they were too big. I didn't realize you have to tighten them up with an Allen wrench. I was really disappointed. Then I looked them up online. I found out how you need to line up the allen screw on the knobs with the slot on your pots. These knobs look and work great. I like how they have one line on them so that it is easy to judge your pot settings.Nihilist74

I used these on my custom Strat that was wired with a blender control. One volume, one tone, and the small knob used on the blender that allows the bridge and or neck pickups to be blended in with it's opposite – giving you the option of all three pickups or any combination. Put all this on a custom made sapele pick guard. The black knobs look really nice with the sapele. Thank you Sam Ash for helping provide the finishing touch to my project!picker tim

My precision 1959 vintage bass tuning key is the same size of 3 1/2" long, but he anchoring plate at the top is 3 1/4" , 3/16th wider at the top than the common replacement key. Co you have such a vintage piece in stock? , I could use a set of four(4). The size I need Bottom:15/16th , the over all measurement is: 1 3/4', the top after angle width is: 1 3/8" 4 mounting attachment screws with face insert, Joe Ross ( 510)m306-8817Joseph

They dont fit genuine American precision bass vintage nek.The back of the tuners are not flat as there is the roll over clamps holding the worm gear.This would require routing out of the back of the headstock.This is something i am not prepared to do to a $2000 neck.Very disappointed.BIg waste of money and time.Purchased gotoh machine heads in Australia and they fitted straight away.Through the Fender ones in the bin.mangosheen2

You are paying for the brand name, its as simple as that. There are better cases for far less money but itll do a job for the occasional bass player.suzeby53

These Genuine Fender Dome Knobs have a great solid feel, and look great too. They're a nice weight also. I actually bought them as replacement knobs for a newer G&L LB100 "P" bass. The knobs on there didn't feel as solid, weren't domed and the diamond cut pattern didn't have as smooth a finish. These are a real improvement.jag67jaguar

I have to say, I don't normally write reviews for product – but this little item changed my mind. I bought one to finish up a parts-o-caster home build, where it was matched with a different knob type. After mounting this one on the guitar, I immediately pulled off the other type and ordered another one of these domed nickel knobs. They are, simply put, the best Tele style knob I have ever used!jagoldtop

ORIGINAL fender parts are always the best way to go whether your replacing old ones or building your own new monster. You can feel it in your hands when you hold them. I buy all my parts from Guitar Audio. They are a fantastic company. Well priced and quick to deliver. Real happy with the knobs. My second build with genuine Fender parts from Guitar Audio and I'll use them on all to come.candelljr123

top quality built. totally silent pickups. perfect. my fender p-bass has an american heavy ash body and maple neck. it produce a punchy highs. i was looking for pickup set that will suppress and cut some of the too-trebley sound. i installed Dimarzio P122. these are excellent pickups, but are not the flavor i wanted. too much highs and too modern in eq and sound color to my taste. since all reviews always point to the Fender Custom Shop pickups as the best upgrade for Precision, i've decided to choose the '63 pickups over the '62. they have a different eq curve. my bet was successful. the p-bass's sounds is now deeper, sweeter, pleasant growl and has a real vintage warmth that i wished to achieve.doron.mckeithen

I love these pickups! They are a great design that date more than 60 years and sound delightful. Unfortunately, with my most recent purchase of these pickups from Guitar Center one of the coils to the pair of pickups was dead. I suspect during the manufacturing process the dead coil itself was tested for continuity at the factory, but, I suspect, in process of wiring my pair of Precision pickups together the integrity of one of the coils was compromised and broken. This can happen and pickup coils lead should always be retested after the solider leads have been attached. I made the same mistake as the factory and did not check the integrity of the pickups prior to installation. Therefore I voided any return I could have made on this item. I had to buy another set which is now working great.David

I bought a Fender Ash body FSR Precision Bass (the sister to the Ash Bodied Standard Jazz Bass everyone is crazy about.) a few years ago at the Manchaester Ct. GC. the Pup's where not to be desired. so I changed them out with the Original They put these in the American Vintage series and there high end Pricision's so these pup's have to be good. and they are. I get compliments on my Bass I also put in a professionaly made Push Back Wired harness with CTS 250k Pots and spraug Orange drop. She littealy is a '62 now. and im in love with the tonal spectrum of this incredible Bass simply by changing to the Fender Original. looking to pure Precision tone cant go wrong with this set.viperBSG

Pre-bent to a slightly tighter radius. This eased installation a great deal. Not cut to uniform lengths, but they were all long enough to get the job done. The cuts were a little sloppy, but they must be filed and finished at the ends either way. Needed very little levelling and dressing. Overall great quality fretwire with uniform radius bends.20 Fingers McGee

The fret wires come in over sized lengths with plenty to work with. I was concerned that the grooves from the removed large jumbo frets would be too loose but they have more than enough tangs that fill and grips the rosewood which can be a bit 'chippy'. I had to adjust the radius of each one which was a bit of a pain that would have been much easier if they left them straight. They filed, leveled and crowned well and are just a bit taller than expected it good quality.001Berek

They are a high quality precision fret wire! After 3 of the Fender frets were installed, I contnually checked fret rocking and was suprised at the results, only 3 frets needed minor leveling after installation was completed. Now my import guitar plays like a High End instrument.timmci85

I tried a couple of cheaper versions around the 3 mark but fell apart after a couple of months and the cable going in was not very tight. Bought this fender product and its just so much better quality. The lead is tighter and snaps in place. You can tell the difference. Will definitely buy again if I need a replacement.torq2004

I put these in an American professional jazz to be able to blend without noise. I chose them because I wanted it to remain a completely Fender bass. They aren't absolutely horrible sounding, but I have decided the only way these companies should make noiseless "single coils" is by using side by side split coils. Not stacked dual coils. Splitting the coils gives good output, attitude, and a low mid bump- you know the kind that makes people love P basses. Everybody is figuring this out except Fender- the greatest guitar maker in the world. Aguilar, Dimarzio, Nordstrand, Seymour Duncan (recently), mojotone (guitar pickups), Fralin. They've all figured out the noiseless thing. I ended up with Nordstrand NJ4SE in one and Dimarzio model J in the other. Love both of my jazz basses now. I love you Fender, but get in the game with your pickups!Andrew

I don't know if this is the LATEST version of the noiseless jazz bass pickups…it is so hard to keep up with Fender as they roll out newer versions, however, this is a great replacement to older jazz bass pickups. It really as close to noise free as you can get as you solo each pickup individually. As most jazz bass players know, the single coil aspect of the jazz bass pickup is GOING to get some hum or noise unless you are playing both the neck and bridge pickups at the same time to cancel out noise. This retains the signature Fender Jazz Bass sound with great clarity with the advantage of being noise free. Highly recommended!!road-cat1

These are a special wind from Tim Shaw, the ultimate pickup guy at Fender. They are capable of perfect vintage deep bass while throwing out strong mids and super crisp, bright highs. Not super hot so you still have to work if you want overdrive distortion, which is a good thing. These have become my favorites for all my Fender builds–basses, teles, and strats.bobvarns

I've played jazz basses for years, recently picking up a late 90s CIJ Geddy Lee Jazz. This bass is based on a 1972 Jazz. The bridge pickup was not working, so I set out to find a good set of pickups. I tried Seymore Duncan Quarter Pounders, a Mexican Standard, and a Fender Custom Shop 60s model not produced any more. By far I liked the Fender Pure Vintage 74s the best. These have a vintage sound, not too hot, with a fuller low end than the 60's custom shop, or my stock pickups in my 2011 am standard jazz (a killer jazz sound). The midrange was very punchy, not too thin, but not fat or thick enough to get lost in the mix. The top end had a bite that lends itself well to a dirt pedal to get some texture. I'm not a huge fan of the bridge pickup soloed on a 70's model jazz, it's too nasal sounding to my ears. I much prefer the 60s spacing. The '74s seem to address that to a certain extent, smoothing out some of the thin nasal bite the 70s bridge pickup is known for. Blended, the sound is full and very punchy. The set growls nicely, in an upper mid sort of way (I see this more due to the 70's bridge pickup spacing) and slapping sounds great if that's your thing. Being mostly a finger player, a fresh set of stainless steel Rounds will get a nice tone that snarls when pushed. I haven't tried flat wound strings, but I'm sure they would sound good. I've never played a 74 jazz, but the pickup set seems to be made for this bass. I think Fender nailed the sound they were looking for here. Construction was typical Fender, nothing fancy and the poles and fiber bobbins were shellac covered. I'm not a huge fan of push back cloth insulated wires, but I had no issues soldering these. So far I haven't had any issues with hum or grounding problems. These are packaged with minimal information, but a schematic was provided for soldering instructions. My one complaint was the lack of information on which pickup was bridge or neck. One was marked with a red dot ( I assumed this was the bridge pickup) but not a single written word regarding the difference. This is annoying at the least, and could be a deal breaker for some if the pickups were are placed incorrectly. Come on Fender, even a note or written mark on the pickup would have been nice. Follow through and do your homework. All complaints aside, these are well worth a try in any jazz, and definitely a home run in a 70's model jazz bass. Add to the fact you can pick these up new for under 100 bucks if you look around, these are worth a try.jamesbaghr

I needed pickups to replace some dead coils on a 1966 Jazz Bass while the originals were out getting rewound, so I bought these '64 Pure Vintage to get me by. They are giving the original coils a run for the money. They possess a bump in the upper midrange that give them the characteristic growl of a vintage Jazz Bass. I'm not certain at all that the rewound 1966 set will go back on the bass unless for resale/originality reasons.gitdoc3qwt

These are great pickups. They exceeded my expectations. They are full and rich sounding and for the price are a superb value. They're less expensive than just about any other good set of Jazz Bass pickups and cost less than having old pickups rewound. I've got active EMG's, Barts, DiMarzios, Aguilars, Fender Super 55's, Seymour Duncans and other Jazz sets in other basses and right now, I'm enjoying the sound of these the most of all.Cajon Crawdad

…and they're exactly what I needed for my '90s-era Crate Electra bass that somehow came up missing one. How does that even happen? Well.when you loan gear out you never know. I only needed one, not four, but hey. if one can go AWOL I reckon there could be more. These are a good match visually, but ever so slightly larger diameter which required a little judicious use of a round file.bp1abe

The only jazz pickup covers I could find. Does not specify American/ Mexican or other country. The Jazz American bass I have has different width pole pieces to keep in line with the tapered spacing of the strings; a great idea I might add, but these are identical pole piece spacing.Limbo

I bought this bag to carry my Gibson ES 175 to gigs, since the hard case is heavy and I have too much stuff to carry already. It is light-weight, keeps its shape sufficiently to provide support and as much protection as you can expect from a bag, yet I can fold it in half and stash it inside another gear bag to get it out of the way on the stand. It has comfortable backpack straps, which is great if you have to walk any distance with your hands full of music and keys or whatever. It has three compartments on the front, each easily accessible and ideal for picks, tuners, metronomes, extra strings, foot stands, iPad, or however much you dare put up against your precious guitar. The largest compartment appears to be big enough to fit standard 8-1/2×11 paper, though I'm all digital these days. Best of all, it has two handles — one on the front and one on the side, invaluable when sliding your guitar in and out of the car.DNWord

I was looking for an affordable case preferably made by Fender for my new Tele. I took a punt and choose this urban style tele bag. It actually fits the guitar very well with little excess room. You cant fit too much stuff in the pockets but its just right for my needs. Feels quite well made, good size, some padding, a couple of pockets, a nice/different colour (which makes me a bit dizzy if I stare at it for too long 🙂 and an extra handle above the pockets. Really like this bag. Cant fault it for the price. Would recommend.700long

After purchasing a cheaper aftermarket guard and noticed how poorly it fit, I broke down and bought the correct one, and glad I did! The fitment, look, and overall quality was awesome and immediately noticed! Like the old saying says you get what you pay for was totally true in this case!garygto54

Any instrument, such as a Fender Precision Bass, can get an immediate facelift with a simple replacement pickguard. This Fender part is a direct replacement for the standard antique white pick guard that came on my P-bass. There are different ideas about what combinations look best, and I think Sunburst and Tortoise Shell is a common match, but NOT with a maple neck. In the end, I was very happy with the way it looked — I think it's got a lot more character then the antique white.Joe G

Nice pg. Relatively easy installation, required minor filling around pick up covers, and neck pocket. First hole was off, needed to drill a small pilot hole to correct… other than those 2 minor issues, the pg fits well, installation went well.. I think it looks very nice, and a lot of my peers like it as well… installed on my am pro p bass, olive green, maple, 4 string, 1st generation.fenderamerican

Works great on Tele with S-1 (this is what is it is sold for) and also Fender Strat 2004 S-1 to replace the smooth S-1 knob. This is why I brought it. Very happy. I like the textured finish over the smooth original part.jonmy7

This new production tube is a great replacement for any gears using 12AU7 preamp tubes. The sound is warm with full density, especially at the low-frequency region. Great C/P value and it is worthwhile for you to try at this low price range.EW

I put this tube in V2 of my Splawn Quickrod and it sounds killer. It helps to tame some of the high end in this amp while still allowing the signature mids to shine through. Highly recommend this tube in a quickrod or other inherently bright amp.Brian

Das Produkt kam nach wenigen Tagen bei mir an (Donnerstag bestellt und Dienstag angekommen). Soweit sehen die Dinger wie beschrieben aus und man bekommt auch gleich noch zwei und das von einer guten Marke. Verkufer und Artikel sind zu Empfehlen.forbidden.kingdom